NWE Paints Ltd  
 
 
 

Home
Up
Catalog
Terms & Conds
Search
View Cart
Checkout
Contact Us
 

Marine, Yacht, Boat Paint - International
Industrial Paint & Metal Fabricator Coatings
Internal Wood Finishes, Paint, Varnish & Sealers
External Wood Finish, Paint, Stain & Preserver
Specialist Paint Coatings
Paint & Coatings For Metal
Spray Paint Aerosol
Coatings For Masonry (Brick, Plaster, Concrete)
Floor Paint & Road Coatings, Smooth & Anti-Slip
Paint Additive, Cleaner, Solvent, & Thinner
Roofing & Bitumen Coatings
Paint Brushes and Tools
Decorators Work Wear, Gloves & Clothing
Paint Strippers & Abrasives
Dust Sheets, Cloths, Wipes, Masks, Sponges etc
Self Adhesive Tapes Masking Tape, Parcel Tape etc

If you would like to place an order, please phone or fax your credit or debit card details - Tel: 01745 342342 or 01745 353165 Fax: 01745 334746 - Website Sales & Technical Information Service. There is a standard £10 + Vat carriage charge on all orders under £150 + Vat.


5Ltr Promastic 600 CT (Please phone 01745 342 342 for more info) 5Ltr Promastic 600 CT (Please phone 01745 342 342 for more info)
INTENDED USE
As a high performance two pack epoxy problem solving ‘one coat, finish for new building and maintenance work requiring only minimal surface preparation. Typical areas of end use are chemical works, fluid flow systems, marine applications, steel structures and flooring.

CHARACTERISTICS
Adhesion promoted coating for use on marginally prepared surfaces (a surface where only minimal cleaning and preparation is possible)
Can be applied to damp steel surfaces which have been cleaned by water jet with no reduction in performance
Fast dry - touch dry after 1-1 ½ hours, dry to handle after 6-8 hours
Low temperature cure down to -5 oC
VOC compliant ‘one coat’ 30% sheen finish - PG 6/23
Applied at 150 microns d.f.t. will give up to 5 years life to first maintenance, in most aggressive exposures. Achievable with one coat application by airless/air assisted airless spray
Applied at 250 microns d.f.t. will give up to 10 years life to first maintenance, in most aggressive exposures. More than one coat will be necessary to achieve this higher film thickness.
Can be over coated by spray after 1-2 hours with Manor 2 Pack Acrylic CV for a high gloss finish.

SUITABLE SUBSTRATES AND PREPARATION
Superb high build primer and / or intermediate coating for high film build specifications.
Can be applied to bare steel, previously painted steelwork and cementious surfaces.
Steelwork: - Ideally Blast Clean to ISO 8501-1:1988E Sa 2.5
- Alternatively, treat any surface corrosion following best working practices making full use of wire brushes, abrasive wheels or needle guns to meet the requirements of BS 8501 St2-3
- airless/air assisted airless spray, apply each coat un-thinned to150 microns dft using a 13-18 thou spray tip.
- conventional spray, HVLP spray, brush or roller, thin by up to 15% Two Pack Epoxy Thinners. (2-3 coats may be required to achieve the desired dft)
Concrete: - apply only to dry, well prepared surfaces after removal of loose cement latence by scarifying, or acid etching, then vacuuming.
- apply the first coat as a sealer thinning 2 parts catalysed paint and 1 part TwoPack Epoxy Thinners
- brush/roll one sealer coat and one or two finishing coats leaving overnight to dry between coats.

Phone 01745 342 342 for prices and availability 



Quantity:



If you would like to place an order, please phone or fax your credit or debit card details - Tel: 01745 342342 or 01745 353165 Fax: 01745 334746 - Website Sales & Technical Information Service. There is a standard £10 + Vat carriage charge on all orders under £150 + Vat.